Service HP3920, D1360, D2466 Lights Blink

Service HP3920, D1360, D2466 Lights Blink

. Way service HP3920, D1360, D2466 Lights Blink:

1. Disassemble the printer by opening the four screws.

2. Check the encoder bar. Encoder is a translator program to the printer motor movements. Usually this encoder bar stained with splashes of ink. This encoder forms such as clear plastic tape and there garis2x code ...

3. Clean encoder with wet wipes. "Beware" do not exist in garis2x the encoder is lost.

4. Try your printer. If still equal, then the encoder must be replaced ....

actually this is not just a printer problem occurs in HP3920, D1360, D2466, but almost all HP deskjet type could experience this trouble.

Good luck ....

Read more »

How Service Epson T20E Dead:

How Service Epson T20E Dead:

1. Disassemble the printer and take boardnya.

2. Check the power output suplynya, that should come out normal voltage 43-45vdc. how to check the voltage

3. If normal power suplynya, you continue the next step is check the diode, as I show in the picture.

4. If the diode short / short circuit, meaning this is the source of the problem.

With this diode konsletnya cause of the electrical power supply 43-45vdc who became ngeground or short-circuited, so that looks totally dead.

Most people think suplynya defective power diode only when existing in the T20E printer mainboard.

5. Replace with regular diodes 1-2 Ampere, if you are having trouble finding a type of diode that.

6. Done, just try ....

Remember ....!! total death cases is epson printer does not just happen on T20E alone, but can occur at T11, C90, C65, perhaps even printer TX101, TX111, etc..

Congratulations work and good luck .......

Read more »

Service As ASF Epson C90 , T20 , T11 Broken

How Service Epson C90 As ASF , T20 , T11 is Broken :

1 . Disassemble the Epson C90 , T20 , T11 and grab you in ASnya ASF broken .

2 . Prepare his tools , among others :

- Wet Tissue which is dried . Because of good fiber wet tissue .
- Paper Clips : for U.S. surrogate .
- Glue Alteco is bottled , you can buy in the store building .
- Cutter : to smooth US-made .

3 . Straighten a paper clip , then heat on the stove .

4 . After a hot paper clip , insert it into the U.S. hati2x ASF broken until a maximum depth but not until translucent plastic tip .

5 . Equate length of the original clip with the United States , that is not too small , so that the US-made clips buckling becomes larger in diameter . See the picture ...

6 . Wrap the paper clip that has been incorporated into the U.S. with a wet tissue which had been dry , and make the size of the U.S. kira2x original . Or larger in diameter which is important papa could not enter the U.S. on top of the pump pit ink .

7 . Squirt glue over the tissue wrapping alteco earlier . Wait some time to dry and harden .

8 . Then use Cutter to soften the tissue that has been dried form as the original ASF U.S. .

9 . completed

Read more »

How to Clean & Maintain Your Inkjet Printer

How you can Clean & Maintain Your Inkjet Printer 

Inkjet printers may seem like very little plastic boxes along with a few electronics crammed within, however they're truly terribly refined bits of hardware. Witness the actual print head zipping back again and forth whilst spraying drops of ink the dimensions of the red blood cell and hitting the actual mark along with which drop lots and lots of times a second. Obtain the thought? Printers would like care and ought to be dealt with to obtain consistent print quality, paper feed, and longer print lifestyle. 

Component 1 : Software program based mostly maintenance 

Begin having a Nozzle Check 

In case your print quality starts to reach down (skinny lines, colours suddenly shift or turn out to be light-weight) the very first factor to carry out is operate a nozzle verify. Utilizing an ordinary section of paper, your printer can print a little check of each and every ink colour and the several nozzles. 

Nearly all inkjet printers have functions referred to as head cleaning and head alignment. 

Head Cleaning 

What to seem for : Sudden colour shifts with your prints. Blacks may begin to get a bronzed look. Lines which operate a similar path like the print head. 

The top cleaning cycle ensures all ink nozzles are distinct and totally free of charge of any obstructions. Constantly operate a cleaning in case your printer has established for longer than a month in among printings. 

Head Alignment 

What to seem for : White repeating lines or perhaps a grid such as pattern in your print can indicate misalignment of heads. Perform this purpose when required. 

You'll would like a few sheets of plain or photo paper to the method. Alignment ensures all of the nozzles are pointing the ideal directing and firing ink inside the correct location. A few newer printer designs have an automatic alignment and clean purpose you are able to operate rather than the actual manual method. 

Exactly in which to locate these tools 

Your printer can possess a upkeep or utility purpose where one can accessibility these and some other functions. A few printers, particularily HP designs, might not have cleanin functions that you may accessibility. 

Upkeep screen shots Mac 

You'll doubtless discover utility and care controls in Method Preferences » Print & Fax » Established Up Printers. 

Cchoose your printer inside the printer checklisting and click Utility close to the highest from the screen.

Epson

Canon

Maintenance screen shots Windows

Newer Epson printers

Older Epson models

Canon Printers

Some Canon printers also have additional cleaning features. As you can see below, this model has a bottom plate and roller cleaning option.

Part 2: Printer Roller and Feed Mechanism Cleaning Tips

If you use your printer often, and especially if you use 2-sided inkjet papers, proper maintenance of the feed rollers is important. Paper leaves behind dust as it runs through your printer. 2-sided papers leave inkjet coating behind, which can be slick. You will eventually notice inconsistent feeding or sometimes your printer will not feed at all.

Also, ink overspray can build up on the rollers below the print head. This results in black streaks, usually on the back of your paper.

Follow the steps below and any feed or streaking issues should dissappear.

NOTE! Red River Paper assumes no liability if you follow these cleaning steps. If you are careless in cleaning your printer, damage could occur. We have been cleaning our printers in this manner for 13 years with no problems to date.

What you will need:

Bottle of rubbing alcohol

Alcohol pads

First, look down the feed tray of your printer - see image below.

Canon printer note! Because Canon printers do not have an on demand paper feed button, you will not be able to reach the entire roller. When running the alcohol soaked sheet through, you will have to make a print - we suggest a text document with only one line or character.

If you put your fingers in the feed path, you will feel rubber coated rollers. Take your alcohol swab and hold it on a roller with your finger. Now, push the paper feed button on your printer - the rollers will move. Don't be alarmed if your finger gets tugged a bit. It will NOT get pulled into the mechanism! Cycle the paper feed a few times and make sure you clean each roller.

If you are having trouble with ink streaks on your paper, try this:

Take an 8.5x11 sheet of plain paper. Soak the interior of the sheet with rubbing alcohol, leaving all four edges completely dry. Run this sheet through your printer 2-3 times front and back. This will clean all of the internal rollers of debris and any ink.

Read more »

Addressing a paper jam in the printer canon

Addressing a paper jam in the printer canon

  Experienced a paper jam or paper jam in the printer we have an event that is not fun , especially when we 're pressed for time to finish the job that requires us to use the printer . Usually when the printer has a paper jam , then shortly after the jammed paper we draw , the printer can not we use right away , and sometimes we have to reset the PC or laptop , the more time would be wasted .

The following are tips to overcome the jam :

Step one: Open the printer cover , and pull the jammed paper by gently way , do not be forced because it can damage the printer .

When the printer when it can not be used , because of a paper jam blinking account after experiencing this , then try the following two steps :

Step two : unplug the printer power cable to reset the printer . Replace the printer power cable and try to use it . Namu when the printer still can not be used , then it can proceed with the next step .

Step three : Try to open the Control Panel > Administrative Tools > service ( for Windows 7 ) or Control Panel > Performance and Maintenace > Administrative Tools > Services ( for Windows XP ) . Open the PRINT SPOILER service , and turn off the process by click " STOP " . Then click Start> Printers and Faxs , right click > Refresh . Spoiler Print Run back service that we stop tadai , by click " START " . The printer is ready to be used again 

Read more »

tips on how to cope with the results of ribbed printer

tips on how to cope with the results of ribbed printer

guys, have you ever experienced this ? yes that time my job was piled however , at the time of going to suddenly ngeprint printout of her striped white line , waah how this , but after a while googling I finally found his way , after the previous admin discussing about android application to learn the Koran at this time we will share how to cope with the results of ribbed printer

consider the following steps ,

1 . The first step to check first hose hose IV ( if your printer infusion )
2 . check printer , is there any foreign objects interfere , for example, scrap of paper or other
3 . then clean the cartridge with cleaning head features
 how:
            a. go to control panel --- > click on the device and printers
            b . right click on your printer - > click printing preferences

            c . Click on the tab on the head cleaning maintenance

            d . click start , and wait until the process is complete

            e . if the process is complete , try reprinting some pictures
             f . if still striped repeat steps c

well that is some tips to overcome the results of the striped printers , printer settings on each is usually different , I have tried these settings using the printer
EPSON TX 111 .

Read more »

How you can Fix the actual Printer Spooler Service

How you can Fix the actual Printer Spooler Service 

The actual spooler service in Windows can stop for numerous factors and typically it could be terribly challenging to obtain it up and running once more. Beneath are a few actions to bring for fixing the actual printer spooler service. 

Restart the actual spooler service 

Step one is to undertake and restart the actual spooler service. You will find a few methods to do that. You ought to first attempt and begin it by way of the actual command prompt. Should that does not function, then you'll got to check out the actual solutions management panel. 

Restart by way of command prompt 

Click Begin and kind " cmd " straight into the quick lookup box and hit enter. For XP users : Begin - Operate, then kind " cmd " and hit enter. 

Inside the command prompt, kind the listed : " net begin spooler " and hit enter. 

Currently verify if you re able to print. Otherwise, proceed to subsequent stage. 

Verify the actual spooler service in Management Panel 

Open up control Panel - Administrative Resources - Services 

Locate the actual print spooler service. You would like to ensure that it service is running and also has a startup kinds of automatic. If it is not the actual case, you are able to double click upon the service and begin it by clicking the actual " start " button. 

When the spooler still has issues, you are able to attempt subsequent actions. 

Verify Firewall 

In case your print spooler service is running or seems to become running however you can't print, it's potential that the firewall configuration could possibly be blocking your printer. Usually if it is the actual case, you'd obtain a message much like : " Printer Qualities can't be displayed. The actual Print Spooler isn't Running ". 

Check this by temporarily turning off your firewall. If you re able to currently print, then it's the actual firewall inflicting the difficulty and you'll would like to feature an exception for the printer (IP) towards the firewall. 

In case you still do not have luck, you are able to attempt subsequent stage. 

Verify the actual Spools Folder 

A few users is unable to restart their printer till they eliminate files inside the spool printer folders. This folder is located in : 

C : WindowsSystem32spoolPRINTERS 

We don't recommend deleting any files using this folder. Rather you are able to transfer the actual files to a special area or rename all of these. Then attempt restarting the actual print spooler service. If the still doesn't function, you'll got to re-install the actual printer drivers. At this stage you ought to additionally scan the body to ensure it's free of viruses and malware. 

Read more »